Product Description


New New New New New!!!!!!!!!!!!!!
You are bidding 1000W wind grid tie inverter , LCD display , No need controller and battery ,input 22-60V,output 180-260VAC Be used 24V/48V (AC wind turbine)
Parameter Table
For AC Output Wind Turbine
Build In Dump Load Controller
Build In High Wind Protection
Build In LCD Display
Build In Electric Brake System
Preface
The grid-tie inverter can transfer wind energy from wind generators directly into the home grid using no extra equipment. It can be connected to any outlet (conventional network) in the home. The grid-tie inverter controls the phase and the frequency and voltage of the power generated by the wind generator. It produces a pure sine-wave and matches that of the grid.
This model grid-tie has designed for wind turbines that put out DC voltage. It has a high voltage protection function, when the wind is too big, and the dump load controlling system can\'t keep the output voltage from the wind turbine, the controller will disconnect itself from the wind turbine, so it is very safe to be used.
Operating Temperature Range
-10 ~ 45 degrees C
Wind grid-series models
WG1000W
WG1500W
WG2000W
Rated AC output power
1000W
1500W
2000W
DC Input Voltage Range
(the test point is at the output of the rectifier)
22-60V /45-90V
45-90VDC
Max output power factor
99%
DC input Reverse voltage protection
Fuse
AC output voltage range
90~160VAC/ 180~260VAC
AC frequency range
46Hz~65Hz
Islanding protection
Yes
Output short circuit protection
Current-limiting
Display
LED
Cooling
Fan
Night Power
Ambient temperature range
-10 ℃~45℃
Waterproof
Indoor Type Design
dump load resistors parameter
R=V2/P=54*54/600 = 4.9 (ohm)
Electromagnetic Compatibility
EN50081.part1 EN50082.part1
Power System Disturbance
EN61000-3-2 EN60950-1
Network test
DIN VDE 126 UL1741

How to use it
On the Terminal Panel of the inverter, there are 5 terminals, 3 terminals will be connected to the AC output from the wind turbine, and 2 black terminals will be connected to dump load resistors.
There are 4 LED indicators, 3 green indicators and 1 red indicator, 3 green LED indicators will start to cycle from left to right when the grid and AC input supply is detected. This indicates the inverter is operating under normal condition. The rate of the cycling is according to how much power is being output from the wind turbine. The more big output power is, the more fast the rate is. If there is no AC grid detected, the red LED will be on, the inverter will not put out power, this is called “Island Protection”.
There is one switch on the panel, the function is electric brake controller, when the switch is put to “Kill” position, the electric brake function will work, this will slow down the rotation speed of the windmill or stop the rotation of the windmill, when the switch is put to “ON” position, then the inverter will work normally.
On the LCD Panel of the inverter, there is one AC output socket, that will connect the AC output cable to home grid. The LCD display will display the grid AC voltage, current , active power and electric energy that combined to the grid .
LCD display Function:
1. Electric parameters measurement function (voltage, current and active power, electric energy ).
2. Running time function (record load cumulative working hours).
3. Backlight function.
4. Power down data save function (save the number of kWh, operation time).
5. Large screen LCD display (display voltage, current, power, active power, cumulative running time)
Key Function:
UP:
Short press will display power, electricity, current and voltage in anti-sequence.
DOWN:
Short press will display power, electricity, current and voltage in sequence.
BACK LIGHT:
Short press will open or close backlight.
There is a Curve Adjustor on this panel, the Curve Adjustor can adjust the inverter to fit the performance of the wind generator, you can adjust the Curve Adjustor according to the rated output voltage of the wind generator to get Max. power that combined to the grid. The scale indicator around the Curve Adjustor is just a reference, you should adjust the Curve Adjustor to get max. power feed to the grid under the normal wind speed at the installed location.
*************************************
Kind note: The wind grid ti e inverter only be used 24V/48V( AC wind turbine), Rather than DC wind turbine.
*************************************
Production line :
Production display:
Option function:
WIFI port, Web/mobile phone App on line monitoring(If you want the wifi monitioring, then you need pay extra cost US$55.07)
Certification
Payment and Return
About payment We accept: TT, Alipay, etc payment methods Return Refund or replacement request is available only the requests within 1 week after parcel received & returning the item as the same condition as received. Please contact us to request a return authorization. Your name, auction number, and reason for return should be included in the email. All items returned must contain all original packaging materials. Please repack the item carefully. Items returned will be tested and a new replacement will be shipped to the buyer immediately when found defective. In the event that a suitable replacement is not available then a refund will be issued. Shipping, handling and insurance fees are non refundable. If the item is found non-defective, the item will be sent back to the buyer at buyer\'s expense. Items returned without RMA number will be refused and returned to the sender. Buyer is responsible for All Return Postage and Shipping Charges. Buyer is responsible for additional shipping costs for items that are returned refused and/or undeliverable. We do not accept any returns without an authorization number on the box or label it is being returned in. Remind The price you paid for the item excludes any customs tax.Our company does not shoulder any duties in destination country. We usually mark the goods as GIFT/SAMPLES on the Commercial Invoice and we are trying to help you to minimize or avoid any GST or V.A.T or other Import Taxes, but we cannot guarantee no tax charges as it is depends on your country\'s policy. Please check with your country customs office to determine what these additional costs will be prior to bidding/buying.

  • Output Frequency: 50Hz /60Hz
  • Output Power: 500 - 1000W
  • Model Number: DEC-WG-1000W-WAL
  • Size: 322x196x88mm
  • Weight: 4.5KG
  • Output Type: Single
  • Brand Name: MAYLAR
  • Type: DC/AC Inverters
  • is_customized: Yes
  • Warranty: 2 years
  • Output Voltage: 90-160VAC/180-260VAC
  • Input Voltage: 22-60V

  • Unit Type: piece
  • Package Weight: 5.5kg (12.13lb.)
  • Package Size: 32cm x 19cm x 8cm (12.60in x 7.48in x 3.15in)

SKU: a40

Related products

Free shipping

Worldwide shipping

Support 24/7

Top Service

Moneyback

Return Exchange

Gifts

Bonuses