Product Description


Product Description:
2.4G Music Controller adopts the advanced micro control unit. It is used for controlling a variety of LED lamp. For instance, LED strips, LED module light , LED light box, luminous characters etc. It has many advantages such as low cost, convenient connection and ease of use; With memory storage function, you can adjust the static brightness, static color, dynamic speed regulation and so on lighting change effects via the RF 2.4G remoter. When it is in sound-control mode, the colors will change with the music rhythm.
Main features:
●Rf 2.4 G wireless remote control signal, sensitive and stable, strong anti-jamming capability.
●Voice receiving sensitivity is adjustable
●3 set of output can realize more convenient for wiring
●Adopt the self-locking socket
●2 kinds of acoustic change model optional
●Wide input voltage high power output
Product
Model:Music-02
Name:2.4G Music Controller
Technical Parameters
● Working temperature:-20-60℃
● Supply voltage:DC5V, 12V~24V optional(please specify required voltage when order is placed)
● Output:Three CMOS drain open circuit output,three-way joint
● Connection mode:Common anode
● Controller size:L155×W75×H30mm
● Unit package size:162*82*58mm
● Net weight:155g
● Gross Weight:205g
● Static power consumption:
External dimension:
Connection description
Power input interface
(adopt the 2 hole plastic green connection seat, with screws on it)
Load output interface
(Three parallel output,4 hole plastic gray connection seat, with card holder function)
Sensitivity adjustment port, to adjust induction sensitivity to sound under the sound-control mode
Remoter button Description
The Remote control parameter are as below table:
Direction for use
●Function introduction:
1、Use the 2.4G frequency RF remote control, no need to make the remote direct to the controller,and the RF remote can controlled it across obstacles.
2、In the open area remote control distance is about 30 meters.
3、Adopt the press key and touch wheel control remote, slightly touch the color wheel can adjust the light’s color temperature smoothly .
● Operation method:
1.Connect the load wire at first, following by the power wire; Please ensure short circuit can not occur between connecting wire before you turn on the power;
2.Only the power button is effective in the OFF station, press the power button for the first time then controller will enter to the last mode before turn of the controller last time (memory off function)
3、After start up,press“Mode+”“Mode-”can realize 22 kinds of effect mode selection.The mode is shown in the table below :
4、When it is in Cyclical mode, press “mode+”, can be back Static red(1), press “mode-”, can be back Red green jump(22).
5、When it is in color wheel adjusting mode, press“mode+” or“mode-”,will be back the last selected mode.
6、When it is in music mode, press“mode+” or“mode-”,will be back the last selected mode.
7、Long press “speed+”,“speed-”“brightness+”“brightness-”, can adjust the speed and brightness.
8、Press“Music mode+” or “Music mode-”,the controller go into voice controlling statue, the output will be changed following the music rhythm. There are 10 change effects available as following:
●Music mode supplemental instruction :
1)DJ music mode: all colors will strobe change following the music/sound rhythm. If no music/sound input or sensed, all colors off.
2)Active music mode: all colors will jump change following the music/sound rhythm. If no music/sound input or sensed, current colors keep lighting.
3)Tenderness music mode: all colors will jump change following the music/sound rhythm. If no music/sound input or sensed, all colors will gradually change.
● Match code and clean code Instruction:
For a new combination, the remote must to match code withe the receiver then it can be used normally. Before match code, you must ensure the LED Controller, power supply and led light are connected correctly, then cut off the power ,and re-power it again.
Match code:Please press the “ON” Button for 5 times within 8 seconds after power the controller, then the output led light will be flash for 6 times, this means the remote is match code with this receiver successfully, they can used normally.
Clean code: if user want to change the light control group,he can clean the code off. After clean code the remote and receiver will be in the initial state. Operation method: Press the “OFF ” Button for 5 times within 8 seconds when power the controller, till the output light flash for 6 times, means clean code successfully.
Remarks:The regular product for sale is a kit (one remote and 1 receiver). The user can re-programmed freely as needed. One remote can control countless receivers, but one receiver can only be controlled by two remotes max.
Typical Application
Cautions
1、This products Input voltage is DC5V/12-24V,other input voltage are not allowed.

  • Item Type: RGB Controler
  • Model Number: 2.4G music RGB controller
  • Power Source: DC
  • Connection Mode: common anode
  • Material: plastic
  • Certification: CE,RoHS,CCC
  • Wattage: 180
  • Max. Load Power: 360
  • Voltage: 12-24V
  • Brand Name: YJBCo
  • Oscillation frequency: 2.4G
  • Controled Method: 2.4G wireless
  • Features: 2.4G music RGB controller
  • Remote Distance: .
  • Applicable Lights: RGB led strip
  • Warranty: 2

  • Unit Type: piece
  • Package Weight: 0.2kg (0.44lb.)
  • Package Size: 1cm x 1cm x 1cm (0.39in x 0.39in x 0.39in)

SKU: a31832

Related products

Free shipping

Worldwide shipping

Support 24/7

Top Service

Moneyback

Return Exchange

Gifts

Bonuses